C64Power Forum
Hardware => Hardware => Wątek zaczęty przez: Raf w 11 Grudnia 2020, 09:59
-
Jak zrobic samemu?
https://1200baud.wordpress.com/2017/03/04/build-your-own-9600-baud-c64-wifi-modem-for-20/
Szybka konfiguracja -> skopiowane z https://www.facebook.com/commodore4ever/posts/instructions-for-setting-up-and-using-your-commodore4ever-wifi-modemfirst-you-wi/1552985544777816/
Plug the modem into your Commodore user port with the label side up (See pic)
• Load CCGMS 2017
• Press F7
• Press 'M' to set modem type as User Port, and then press 'B' to select 300 baud
• Press Return to go back to terminal
• Press Return and you should see the Modem Info on the screen. If not type 'ati' then press return and the info should pop up.
• Hit F8 to go to Ascii mode (THIS IS IMPORTANT AS YOUR PASSWORD AND ID WILL NOT ENTER CORRECTLY IN GRAPHICS MODE!)
• Enter your ssid and password with the following terminal commands: at$ssid=ssid then press return and then at$pass=password then press return.
• F8 to go back to the Graphics terminal
• Type 'atc1' to connect. You may have to do this a few times to get it to connect
• Type the commands 'at&p0' and press return then 'at&k1' and press return . Without doing this 9600 baud will lock up your c64
• Change the baud rate by typing 'at$sb=9600' then press return.
• Press F7 and select modem type by pressing 'M' as Up9600 and then change the baud rate by pressing 'B' to 9600
• Save your settings by pressing 'S'
• Press Return to go back to terminal
• Type 'at&w' then press return to save the settings to the modem
*Type atds1
Enter NEW at the prompt to register!
Now that you have registered on my BBS you can ask questions and leave comments or suggestions.
Next lets go over the list of commands for the modem.
at? - This will list the commands available on the modem.
atdt - Dial host.
example:atdtcommodore4everbbs.exampl:6400
atds- Speed Dial. This will dial the address that is store in the
saved slot (0-9). example:atds0 This will dial the host
saved in slot 0
at&z- This will save a host to the desired slot (0-9) example:
at&z0=commodore4everbbs.exampl:6400 This will save
host to speeddial slot 0
atnet- This sets telnet control to on or off (0-1) This does not
need to be changed as it is set correctly by default (0).
ati- This will list all of the current modem information.
at&w - This will save changes to modem setting.
at&v - This will show the current and saved modem settings.
at&f - Return all settings to default.
at&p - Sets modem polarity (0=inverted, 1=Normal) example:
at&p1
ate - Sets terminal echo on or off (0=off, 1=on) example: ate1
at&ssid= - Sets wifi ID. example: at$ssid=yourmodem
at$pass= - Sets wifi password. example: at$pass=modempass
at&k - Sets modem flow control (0=off, 1=on) example: at&k1
+++ - Enter modem command mode
ath - Hangup. Only works while in command mode.
ato - Exit modem command mode
There are other standard Hayes compatible commands but the ones listed are the most important.
inny manual:
https://borgelin.org/C64-WiFimodem-manual.html
Soft:
Terminal CCGMS 2020 : https://csdb.dk/release/?id=191712
Klient IRC: https://csdb.dk/release/?id=197138
Klient telnet: http://zimmers.net/geos/geotelnet.html
-
Masz może w planach sprzedaż tego sprzętu?
-
https://allegro.pl/oferta/modem-wi-fi-strikelink-wifi-9600bps-9796227237
Ostatnia sztuka z partii, nie wiem czy bede wznawiac (nawet jesli tonza miesiac-dwa)
-
Ale to prosty sprzęt. Dwa z trzech elementów mam w domu, więc chyba zlutuję sobie to sam. Sroki, ale w moim przypadku ten zakup nie ma sensu.
W każdym razie dzięki za linki i ciekawy temat.
-
Przydatna rzecz - Monitor dostepnych serwerow BBS:
http://cbbsoutpost.servebbs.com
Dodatkowo dobry film pokazujacy proces konfiguracji:
https://www.youtube.com/watch?v=zKlmqhTS5UA
PS. Wznowilem oferte, mam jeszcze kilka sztuk dostepnych.